EWP^®80 Combo Remote Electric Water Pump & Controller (12V) (Part #8907)

The EWP^®80 is available for purchase in following options:

• Pump Only (Part #8105) 
• Kit (Part #8005)
• Combo with Controller (Part #8907)

The EWP^®80 Electric Water Pump and LCD EWP^®/Fan Digital Controller Combo – simple, do-it-yourself, easy to install, designed to complement or replace your existing belt-driven, mechanical water pump and engine thermostat, and operate your Thermatic^® Fan.

The EWP^®80 will fit most vehicle makes and models fitted with naturally-aspirated or turbo engines up to two litres, 12 Volt Only.

The revolutionary, Australian-designed EWP^®80 is made from anti-corrosive, lightweight, heat-resistant, glass-filled nylon and incorporates a ceramic faced seal for long-life durability.

The EWP^®80 greatly enhances engine cooling control while giving you added power and improved fuel economy. By removing the parasitic power losses of a belt-driven, mechanical water pump the EWP^® can provide up to 10kW (13hp) of extra power and increased torque and used extensively in Intercooler applications.

EWP & CONTROLLER INSTALLATION DEMONSTRATION

Combined with an LCD EWP^®/Fan Digital Controller will manage both the EWP^® and Thermatic^® fan operation. The Digital Controller will vary the speed of the EWP^® in response to the engine’s coolant temperature. Multiple temperature settings are provided on the Controller for either maximum power or fuel efficiency. The Thermatic^® Fan/s will be activated automatically once the engine coolant rises 3°C (5.4°F) above the targeted (set) temperature. The Digital Controller will automatically run on for three minutes (or to 10°C / 14°F below the set temperature) after engine shut down, eliminating ‘heat soak’ and extending engine life. The EWP^® Controller Combo Pack is supplied in a do-it-yourself kit with everything you need for fitment to your vehicle’s engine, including an easy-to-follow DIY instruction booklet.

The world’s most advanced total engine cooling management system:

 universal fit

 more power

 more cooling

 increase fuel efficiency

 extend engine life

 world-leading technology

EWP^® INSTALLATION OPTIONS

Installing an EWP^® as an AUXILIARY PUMP

• Leaving the mechanical water pump in place, install the EWP^® into the bottom radiator hose.
• Remove the thermostat and drill two approx. 3mm (1/8") holes in the thermostat plate to allow some coolant circulation when the thermostat is closed. Re-install ensuring that the thermostat housing is clean and a new gasket is used if required.

EWP^® INSTALLATION – disabling Mechanical water pump

• Leaving the mechanical water pump in place, install the EWP^® into the bottom radiator hose and remove the manufacturer’s thermostat.
• You will need to bypass the water pump pulley by installing an appropriate length belt (not supplied). This method makes for an easy installation.
• If running the pump continuously remove the thermostat and drill two approx. 3mm (1/8") holes in the thermostat plate to allow some coolant circulation. Re-install ensuring that the thermostat housing is clean and a new gasket is used if required.

In both these cases, the EWP^® will pump past the impeller of the mechanical water pump.

Disengaged mechanical water pump (recommended)

• Remove the mechanical water pump and remove the thermostat.
• Then remove the impeller from the mechanical pump shaft. Retain the mechanical water pump using the pump pulley as an idler to avoid re-routing the drive belt.

• Block any bypass passages and re-install the disengaged water pump ensuring that all gasket surfaces are clean and the new gaskets are properly fitted to prevent leaks.
• Install the EWP^Ò into the bottom radiator hose.

Removed mechanical water pump (Ideal)

• Remove the mechanical water pump and thermostat from the engine.
• Install a Davies Craig EWP^® Header Adaptor or blanking plate (not supplied). Ensuring the gasket surfaces are clean and the appropriate gasket or sealant is used to prevent leaks.
• Install the EWP^® into the bottom radiator hose. This method will require you to modify or replace the standard radiator hose.
• Install an appropriate length belt (not supplied) to drive the accessories.

In most cases EWP^® will be adequately supported by the radiator hose. Where mounting is required, the EWP^® must be soft mounted to protect against vibration. For the EWP^®115, EWP^®140 and EWP^®150 Part #8700 or #8710 Mounting bracket is recommended.

For further information, see Product Information